Our Products

EM1000

EM1000 Quad High Speed UART Programmable Embedded IoT Module

In full production, but not recommended for new designs. Consider the EM2000 device instead.

The EM1000 is a full-featured Tibbo BASIC/C-programmable IoT Module with Ethernet, as well as optional Wi-Fi* and GPRS** connectivity. The EM1000 has four UARTs.

The device’s capabilities are further enhanced by the onboard flash memory with hardened fault-tolerant file system, as well as the EEPROM and RTC. The RTC backup supercapacitor can be installed on the module (“-S” ordering option) or connected externally.

The EM1000 has 54 general-purpose I/O lines and can control an externally attached LCD, keypad, buzzer, card readers, serial devices, and other circuitry.

Device pins have the standard 2.54mm (100mil) pitch. This makes the module ideal for prototyping, low-volume production runs, and hobbyist projects.

Module testing and evaluation can be performed with our EM1000TEV and EM1000EV kits. The EM1001 board, a close relative of the EM1000, is also a very convenient testing option.

The EM1000 may be uploaded with a fully functional serial-over-IP (SoI) application that turns the EM1000 into a powerful serial over IP (SoI) device, a.k.a. the Ethernet converter.

Key Features:

  • High-performance CPU (T1000)
  • 10/100 Base-T Ethernet port(no RJ45/magnetics)
  • Optional GPRS connectivity(requires an external modem)
  • 4 UARTs support serial, Wiegand, and clock/data streams
  • 4 synchronous serial ports with SPI and I2C modes
  • 54 general-purpose I/O lines
  • Supports externally connected LCDs and OLEDs
  • Supports external matrix and binary output keypads
  • Can drive an externally connected buzzer
  • Onboard RTC (optional backup supercapacitor)
  • 1MB flash disk for TiOS, application code, and file system
  • 2048-byte EEPROM
  • 3.3V power
  • Prototyping-friendly 2.54mm (100mil) pin pitch

Technical Data

Technical Data:

  • 10/100BaseT auto-MDIX Ethernet port (no magnetics)
  • Optional Wi-Fi interface (requires the GA1000 add-on module)
  • One serial port (CMOS-level): ◾Baudrates of up to 460,800bps
  • None/even/odd/mark/space parity modes
  • 7 or 8 bits/character
  • Full-duplex mode with RTS/CTS and XON/XOFF flow control
  • Half-duplex mode with direction control
  • Encoding and decoding of Wiegand and clock/data streams
  • 8 general-purpose I/O lines (including 2 interrupt lines)
  • 512KB flash memory for firmware and application
    Optional 1MB flash disk (requires an external SPI flash IC)
  • 208-byte EEPROM for data storage
  • Three control lines for status LEDs
  • Control lines for two external dual-function status LEDs
  • A separate control line for the Ethernet link LED
  • External reset source required
  • Based on the T2000 IC
  • Power: 260mA @ 3.3V (100Base-T mode)
  • “Vertical slice” form factor
  • Dimensions (HxWxT): 16×18.5×6.5mm
  • Operating temperature range: -40 ~ +80C
  • Firmware is upgradeable through the serial port or network (including “cold” firmware uploads through the network)
  • CE- and FCC-certified

Related Articles

Similar Articles

Product Inquiry

Please contact us. We will get back to you as soon as possible.
Product Inquiry

Product
EM1000

I have taken note of the privacy policy. Note: You can revoke your consent at any time for the future by sending an email to info@mev-elektronik.com.

Your Contact Person

Guido Gandolfo

Product Marketing Engineer

+49(0)5424 2340-57

write email
Contact us!
Please enter one ore more search terms.
crossmenu linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram